Quadra-Fire 4300 Series Instrucciones de operaciones descargar pdf (Pagina 6)

CLEARANCES TO COMBUSTIBLES (UL AND ULC)

Page 6

FLOOR PROTECTOR: Floor

protector must be noncombustible

material or equivalent, extending

beneath heater and to the front/

sides/rear as indicated.

NOTE: A 3/8” (10mm) minimum

thickness tile or equivalent is

recommended, but not required.

Minimum clearances to Combustible Materials (in inches and millimeters) for Quadra-Fire 4300 Series

Chimney &

Installation Clearance Connector A B C D E F G

Residential Standard Note 1 19”(483) 32”(813) 21”(533) 16”(406) 22”(559) 12”(305) 52”(1321)

Residential/Mobile Home Reduced Note 2 10”(254) 27”(586) 18”(457) 7”(178) 17”(432) 9”(229) 52”(1321)

Alcove Standard Note 2 & 3 10”(254) 27”(586) 18”(457) 7”(178) 17”(432) 9”(229) 52”(1321)

Minimum clearances to Combustible Materials (in inches and millimeters) with top shield

Minimum clearances to Combustible Materials (in inches and millimeters) for Quadra-Fire 4300 Step Top

Chimney &

Installation Clearance Connector A B C D E F G

Residential Standard Note 1 19”(483) 32”(813) 18”(457) 16”(406) 22”(559) 9”(229) 52”(1321)

Residential/Mobile Home Reduced Note 2 10”(254) 27”(686) 12”(305) 7”(178) 17”(432) 3”(76) 52”(1321)

Alcove Standard Note 2 & 3 10”(254) 27”(686) 12”(305) 7”(178) 17”(432) 3”(76) 52”(1321)

Minimum clearances to Combustible Materials (in inches and millimeters) with extended top shield

Chimney &

Installation Clearances Connector A B C D E F G

Residential Standard Note 1 15”(381) 24”(610) 18”(457) 12”(305) 14”(356) 9”(229) 52”(1321)

Residential/Mobile Home Reduced Note 2 10”(254) 24”(610) 12”(305) 7”(178) 14”(356) 3”(76) 38”(966)

Alcove Standard Note 2 & 3 10”(254) 24”(610) 12”(305) 7”(178) 14”(356) 3”(76) 38”(966)

Note 1: 6” (152mm) diameter single wall, minimum 24 MSG black or blued steel connector pipe with a listed factory-built type HT

chimney suitable for use with solid fuels or a masonry chimney.

Note 2: 6” (152mm) diameter double wall insulated connector pipe with listed factory-built type HT chimney or a masonry chimney.

(Mobile home venting system must be equipped with a rain cap and spark arrestor.) For installations with a preexisting class A

chimney system, a listed stainless steel chimney liner should be installed, or the existing chimney examined by a chimney sweep for

acceptable further use.

Note 3: Alcove specifications: Maximum depth of alcove shall be no more than 48” (1219mm). For additional alcove information

and clearances, refer to clearances to combustibles above.

NOTE: Unit is approved for use with listed double wall air-insulated chimney connector or elbows.

When locating your stove consider safety, convenience, traffic flow, and the fact that the stove will need a chimney and chimney

connector.

FLOOR PROTECTION: Floor protector must be noncombustible material, extending beneath heater and to the front/sides/rear as

indicated.

NOTE: A 3/8” (10mm) minimum thickness tile or equivalent is recommended, but not required.

NFPA 211: Use a noncombustible material with 1” (25mm) ventilated air space to reduce clearances. However, this is not to exceed

50% of Quadra-Fire’s specified clearances.

NOTE: Must follow NFPA 211 spacing and materials to qualify. It is also subject to local jurisdiction.

AVOID FIRE: Maintain the designated clearances to combustibles. Insulation must not touch the chimney. You must maintain the

designated air space clearance around the chimney. This space around a chimney is necessary to allow natural heat removal from the

area. Insulation in this space will cause a heat buildup, which may ignite wood framing.

1 2 3 4 5 6 7 8 9 10 11 ... 27 28

Comentarios a estos manuales

Sin comentarios

Quadra-Fire 4300 Series Instrucciones de operaciones Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Estufas Quadra-Fire 4300 Series